How to see the model room
1. For one week construction site:
Mainly visualize their materials, and examine whether the decoration company's crafts are in line with the scene of the company's work, the decoration of the materials on the construction site, the necessary facilities (such as fire prevention), the completeness of the facilities, and the exchanges between workers and workers, whether there is a temporary consolidation What about a team? A lot of exchanges with workers (remember workers, not foremen) to view the quality of the overall staff, to facilitate the subsequent link, for the environmental protection of materials, should see the decoration company at the scene of the material sampling report, a closer look at the above Marking is consistent with the site material.
2. For the concealed works site at Shi:
From the first section of the complex, and again see the transformation of the circuit embedded, whether it is tidy, whether the interval is fixed according to the specification (normal 50CM), the hardness of the pipe is pinched by hand, whether it is squeezed, whether the PVC joint is fixed and whether the fixed part is Solid, for the wiring box, take a foot on the top to see if it can crush, because the junction box is the hidden place where the owner needs to directly face the switch in the future, its quality is important, for the wooden keel ceiling, a To see if the fire paint brushing is uniform, and second, to see whether the scaffolding of the keel, the spacing of the reinforcement bar spacing, for the waterway renovation, decoration companies most likely to cut corners of the joint is to break the beam, such as Pirza, some people with Pilesa , The above logo, the owner is easy to see, Oh, but forgot to look at the joints, Pilesa joints are more expensive than the pipe N times, and the joints directly affect the quality of water supply, because that is the maximum water pressure The bad joints are prone to problems.
3, for the construction of the site:
In the middle of the general construction, tiles should be tiled, and the base of the wall is also being processed. The panel surface of the wood board has been installed. Basically, the basic living should be out. The highlight here is that the oil mixing practice is super. Whether the splicing carpenter of the length veneer panel has a chamfered seam or not, some people say that it is the problem of the seaming of the oilworker. Even I think that this is a woodworker, and the oiler uses a small knife to cut the depth and opening degree. In the future, it is easy to spit white, long and dumb joints, whether next to use the reinforcement method, pinch about the strength of tile cement sand, whether there is a level ruler around the tiler, whether with a line, the level is in this construction is still Often used? See if there is any wet cement mark on the site. Check the construction drawings on the site. Can it be constructed according to the original drawing? Can it show the effect on the drawing? Does the staffing of the construction site at half of the construction site have the appearance of a pull person? Now the work site Neatness, and stacking with the remaining piecemeal material.
4, on the post site:
A. Check whether it is consistent with the design drawings, the overall perception, first determine whether there is a tacit agreement between the cooperation between the designer and the worker.
B, carpentry look, yin and yang angle work is neat seams neat, the same cabinet decent surface material (pattern is the same), leaving the seams of the practice is the gap neat!
C. Oilworker's point of view, whether the paint is sprayed, whether there is an irregular reflection (can be traced back to the use of the material), whether the base putty (oily, water-based) figure foam is even, and whether there is a leak in the polishing (check the sense of responsibility) The most easily forgotten place is the top of the wooden case. Whether the oilworker polishes and makes up the brush (touch it with his hand to see if there is any burr or smoothness)!
D, bricklayer's point of view: in the construction site to find two kinds of tools, one is a two-meter by the ruler, one is a square, first check the gap is neat, and then use the ruler to see the verticality and flatness of the brick, the smaller the error rate The better, the national standard is 2MM, use a square to check whether the tiling of the yin and yang corners is square, where the corners are touched, and whether the grinding angle of the wall tiles is neat, and whether the emptying rate of the wall and the floor tiles is less than 5%. Putty, is it easy to drop?
E. Finally, take a look at the overall effect of the things you do, and see if there are some places where the two types of jobs are transferred.
Model room villa design floor decoration decoration company paint cement switch model design decoration look decoration company okay decoration model room
Stainless Steel External Tooth Lock Washers, with high quality sus304 316 which are one of the highest forms of corrosion resistant steel, making it last longer than other hardware on the market today.and it is great for both indoor and outdoor using. The stainless steel provides excellent rust resistance in water applications.Custom packing for export, carton packing or plastic bags, or according to your request. We have much stock of those items, more sizes and standards for your choice.
Lock washers with external teeth, also known as external tooth lock washers or external serrated lock washers, are a type of fastener used to prevent loosening or rotation of bolts, screws, or other threaded fasteners.
These washers have serrations or teeth on the outer edge, which bite into the mating surface or the underside of the fastener head when tightened. This creates friction and helps to prevent the fastener from loosening due to vibrations or other forces.
The external teeth on these washers are designed to dig into the material, providing a more secure grip compared to regular flat washers. They are commonly used in applications where there is a risk of fastener loosening, such as automotive, machinery, or construction industries.
Lock washers with external teeth are typically made from materials like steel, stainless steel, or other metal alloys. They are available in various sizes and can be used with different types of fasteners, depending on the specific requirements of the application.
Lock Washers External Teeth,External Tooth Star Washer,External Tooth Washers,External Teeth Lock Washer
Taizhou Wanluo Hardware Products Co., Ltd. , https://www.wlhardware.com