How to maintain computer needle car
2023-06-10 12:10:14
The reasonable working environment of the computer needle car, first of all, do not install equipment in places with strong electric sound or high frequency electric welding. Strong electric sound will affect the equipment or cause the equipment to work normally.
How to maintain computer needle car
1. The reasonable working environment of the computer needle car, first of all, do not install the equipment in places with strong electric sound or high frequency electric welding. The strong electric sound will affect the equipment or cause the equipment to work normally.
2. The indoor temperature of the workshop should be between 5 °C and 35 °C. The temperature is too high or too low, which will affect the normal operation of the equipment.
3. Humidity will cause short circuit inside the machine. The relative humidity should be kept at 45%-85%. It should not be installed together with the ironing equipment with steam.
4. Dust can easily corrode the circuit board, so the equipment should be kept clean and the workshop should be kept clean.
5. A regulated power supply (power supply or voltage regulator) should be used. The power supply required for the equipment must be grounded. It is strictly forbidden to set up a fire line on the 380V three-phase four-wire three-phase fire line, and then take a zero line as the 220V power supply, as the power line of the computer sewing equipment, which often causes equipment accidents or crashes (mainly Is the voltage is too high or too low). Maintenance personnel often do not pay attention to this, and desperately adjust the equipment, resulting in a lot of unnecessary trouble, in fact, only need to stabilize the power supply, the equipment will return to normal immediately.
6. Any computer sewing equipment should not exceed ±10% under the rated voltage of the power supply bureau. If it is too large or too small, it will affect the equipment's failure to work normally, but the power supply should be greater than the power consumption required by the sewing machine.
7. The machine should be protected from direct exposure to outdoor sunlight. The temperature generated by the light on the machine head can easily burn out the display. The light on the frame can easily burn out the chip inside the main unit, causing a major accident, so the sun can be directly exposed. In the workshop, the doors and curtains should be decorated.
8. Lightning weather should be turned off, because lightning will directly affect the normal operation of the equipment.
Http://news.chinawj.com.cn Submission:
How to maintain computer needle car
1. The reasonable working environment of the computer needle car, first of all, do not install the equipment in places with strong electric sound or high frequency electric welding. The strong electric sound will affect the equipment or cause the equipment to work normally.
2. The indoor temperature of the workshop should be between 5 °C and 35 °C. The temperature is too high or too low, which will affect the normal operation of the equipment.
3. Humidity will cause short circuit inside the machine. The relative humidity should be kept at 45%-85%. It should not be installed together with the ironing equipment with steam.
4. Dust can easily corrode the circuit board, so the equipment should be kept clean and the workshop should be kept clean.
5. A regulated power supply (power supply or voltage regulator) should be used. The power supply required for the equipment must be grounded. It is strictly forbidden to set up a fire line on the 380V three-phase four-wire three-phase fire line, and then take a zero line as the 220V power supply, as the power line of the computer sewing equipment, which often causes equipment accidents or crashes (mainly Is the voltage is too high or too low). Maintenance personnel often do not pay attention to this, and desperately adjust the equipment, resulting in a lot of unnecessary trouble, in fact, only need to stabilize the power supply, the equipment will return to normal immediately.
6. Any computer sewing equipment should not exceed ±10% under the rated voltage of the power supply bureau. If it is too large or too small, it will affect the equipment's failure to work normally, but the power supply should be greater than the power consumption required by the sewing machine.
7. The machine should be protected from direct exposure to outdoor sunlight. The temperature generated by the light on the machine head can easily burn out the display. The light on the frame can easily burn out the chip inside the main unit, causing a major accident, so the sun can be directly exposed. In the workshop, the doors and curtains should be decorated.
8. Lightning weather should be turned off, because lightning will directly affect the normal operation of the equipment.
Http://news.chinawj.com.cn Submission:
Dc Axial Fan,Blower Fan 12V,Extractor Fan,Machine Cooling Fan
Crown Electronics CO., LTD , https://www.crownelectronicstw.com