Home decoration troubles that must be known in winter decoration
In winter decoration, although there are some unfavorable weather factors, as long as it is handled properly, the quality of the project can still be guaranteed. For consumers who want perfect decoration, they must do their homework in advance. So, what are the problems and problems that are often encountered in decoration? We ask experts from professional supervision companies to talk about where renovations are easy in their eyes and remind consumers to pay attention to the construction process.
Dream Luoshi home    Seastar shutters Â
Wall surface
Substrate handling is key
The flat and beautiful wall can be the perfect basement for family use. The problem of the wall is mainly divided into two aspects: the surface and the base. From the aspect of surface appearance, uneven painting of paints, flow falling, drumming, and warping are common problems in acceptance. However, they are all caused by poor construction techniques and processes, so consumers are Check carefully when checking. In addition, it should be noted that when painting the walls, it is necessary to follow the process of applying the primer two times. In addition, the amount of latex paint is 5% to 10%. If excessive water is added, it may appear. Brushing uneven phenomenon, which is often used to save money, consumers should pay attention to supervision and inspection.
In addition, wall peeling is one of the common wall problems caused by the insufficiency of substrate treatment. Before scraping the putty, it is necessary to inspect the basement layer of the wall. If the substrate is not good enough, it must be treated after the eradication to meet the required standards before scraping the putty. If not for a maximum of one year, the wall covering will fall off. If the flatness of the base is not enough, a large area of ​​empty drum sounds can be heard by knocking against a wall with a small hammer. Such a wall covering will take a long time to fall off.
The top
Multiple inspections inside the ceiling
The most common problem in the top project is that the internal components of the ceiling are not strong enough to cause the ceiling to sink. Supervisors recommend checking the expansion screws, locks, clips on the fixed boom, and the firmness of the keel before suspending the gypsum board. In addition, it is also necessary to check whether the wires and pipes installed in the ceiling are firm.
Water circuit
Material inspection is the most important
Hydroelectric reform is a hidden project. Once it is enclosed in walls and ground, it is difficult to handle it again. Therefore, it is the most important task in acceptance. During the supervision process, the supervisor had encountered some unreasonable materials used by the construction team. For example, the thickness of the pipe wall used was not enough, the wire was not in compliance with the national standard, and the products passed the 3C certification. All these were required by the consumers to enter the market. When you check it.
In addition, the depth of slotting of the water circuit is not enough and often occurs, which will cause major problems such as leakage of water in the later stage, drumming on the wall, and inspections during acceptance. In addition, in the circuit laying process, the “winding†is most likely to increase the charging problem. For example, if a socket is located at a distance of 1m and 2m from the original socket of the house, it can be horizontally slotted as long as it moves in parallel. However, some construction parties will take wires to the distribution box to increase the length of the line. In addition, in the floor drain of the bathroom, a slope of one-thousandth to three-thousandths of a degree should be taken before paving, otherwise, the phenomenon of flooding will occur, and many construction parties have neglected this point. Even if it is found during late acceptance, It is also very troublesome to handle. If it is modified, it is necessary to remove the tiles and redo the waterproof.
ground
Paste fastness problem
Tiles are the most prone to problems in surface engineering. It is common for tiles to have insufficient fastness and poor paving. Before putting on the tiles of the bathroom, the phenomenon that the wall surface is not treated by pulling hair is very common. Because the ceramic tile has weight, if it is not done, the firmness of the cement paste is not enough, and it may fall off over a large area in about half a year. In addition, there are often cases where the tiles are plastered with different crevices and are not aesthetically pleasing. To prevent this, it is advisable to check the size of the tiles before laying them, to ensure that each tile is of the same size, and it is best to do a pre-tap before the tiling. Rows—Draw the tiles on the wall with a line of paint. At least one row of tiles should be drawn. Consumers can check in advance to see if the tiles match their own ideas. In addition, consumers should be reminded that after three days of affixing the tiles, they can use a small hammer to percussion check, otherwise the ceramic tile bonding is not firm enough and it is likely to fall.
Tile aisle ceiling paint socket home latex paint beautiful shutter bathroom tile bathroom ceiling material bathroom size bathroom ceiling bathroom waterproof bathroom leaking tile adhesive decoration home ld tile
CHANGZHOU ANTALYA TOOL AND MACHINERY CO., LTD. , https://www.atly-tool.com