How to Accept Acceptance of Fully Furnished Room Solid Wood Flooring

The quality of the floor directly affects the quality of living and overall appearance of the house. Therefore, in the inspection process, the floor acceptance is an important link in the acceptance process of the fully furnished room. Fully-furnished room wooden floor "common diseases" mainly include: color, drum, deformation, there is a deviation of height and when walking stampede, as well as blinking, cracks, scratches and so on. Home inspectors introduced: At present, the floor of the renovated house is more prominent. Therefore, the acceptance of the floor has become a problem that owners must pay attention to. Today's talk about how to accept the floor.

1, see the color of the floor is the same

If the color difference is too large, directly affect the appearance, you can ask for exchange; if the color is too consistent, almost no color, it depends on the floor surface pattern is the same. If the pattern is almost the same, it may be craft wood floor, not the material floor of the so-called precious wood species. Now some flooring material suppliers use ordinary wood flooring materials, but in the surface paste a layer of valuable wood veneer to shoddy, said to be moisture-proof, in fact, is afraid of being seen opposite the pattern and the front of the inconsistencies .

2, see if there is a sound floor

When walking on the floor during inspection and acceptance, the footsteps must be increased. In particular, the wall and door openings must be checked and accepted. If there are sounds, repeat the walk and determine the specific location of the sound. In this case, you can ask to remove the resurfacing. The site where there are sounds is caused by non-standard operations and unqualified materials used by construction workers during the construction process. The operation is not standardized, mainly reflected in the fixed keel is not solid; material failure is mainly reflected in the ground keel without drying. Some renovation construction units use undried keel construction. The surface shows signs of drying. In fact, they did not dry. The keel with high moisture content will shrink in volume during the natural drying of the wood, causing looseness.

3, acceptance of the floor deformation, warping

Acceptance method is to use a 2 meter long ruler, leaning on the floor, the flatness should not exceed 3 mm. More than a few measurements, if the passing rate of 80% or more is considered qualified, and vice versa, is unqualified. Sometimes we find that the floor is partially arched: if it is a solid wood floor, it is because it is too tight or the floor is too dry (water content is too low); if it is a laminate floor, it is a poor quality floor. Therefore, the arching of the floor is a serious quality problem.

4, the acceptance of the baseboard

Baseboard and door frame clearance ≤ 2 mm; skirting line spacing between joints ≤ 1 mm; baseboard and floor surface clearance should be in the range of 3 mm to 5 mm; height difference of the baseboard buckle should be ≤ 1 mm.

5, the acceptance of the buckle

The door clasp should be installed directly under the door. It is advisable not to leave the inside and outside of the door after closing the door. The gap between the clasp and the door is between 3 mm and 7 mm, and the door can be opened and closed freely. The buckle should be installed firmly and stably. You can kick the middle part of the buckle to check if the sides of the buckle are tilted or loose and there is no abnormal sound.

6, the final acceptance surface

Whether there are blinks, cracks, scratches. Commonly due to the untreated keel, there are locusts inside. When it was found that there was a blink, the floor was already almost cracked; gaps and scratches were known at a glance. Regulations: floor gap should not be greater than 0.5 mm; scratches are mainly due to rough decoration, such as waxing method can not be repaired, it must be exchanged.

The materials and grades of wood flooring are in line with the design requirements. The moisture content should be about 10%. The keel and studs should be treated for anti-corrosion treatment. The wooden keel should be firmly and flatly installed, and the spacing and fixing method should meet the specification requirements. Solid, no loose, firm paste, no empty drum, the use of plastic varieties meet the specification requirements.

Visually inspect the surface of the wooden floor for planing, grinding, no scars, russia and burrs, with clear patterns, uniform color on the surface of the clean oil, proper paving direction, tight seams on the surface layer, staggered joint locations, and clean surfaces. The skirting boards have tight joints, smooth surfaces, and a uniform height and wall thickness. Checked with a 2-meter ruler, the ground flatness error is less than 1 mm, the gap width is less than 0.3 mm, the mouth plate straightness error is less than 3 mm, and the seam straightness error is less than 2 mm.

Flooring installation decoration

Water Purifier Kitchen Faucets

The faucets used in general households are unified, and there is no distinction between drinking water and water. But in some western countries, to provide special water purification pipeline, it is required to have a water purification faucet. There is no difference between the clean faucet and the general faucet, but the raw water is different.

Water Purifier Kitchen Faucets,Kitchen Mixer Faucets For Restaurant,Brass Water Purifier Kitchen Faucets,3-Way Drinking Water Filter Kitchen Faucet

Kaiping Jenor Sanitary Ware Co., Ltd , https://www.kpjenorsanitary.com