Home>Bearing knowledge>Analysis of the cause of FAG bearing attack

/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131";

Analysis of the causes of FAG bearing attack

---

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';

1, the bearing temperature is too high: in the organization of the work; the part of the bearing of the device promises a certain temperature; when the hand touches the tissue shell; should not feel the trick is normal; otherwise it indicates that the bearing temperature is too high.
The reason why the bearing temperature is too high is that the smooth oil quality does not meet the demand or the enthalpy change; the smooth oil viscosity is too high, the tissue device is too tight (the gap is lacking), the bearing device is too tight, the bearing race is changed on the shaft or the shell, and the load is over Large, bearing cage or rollover fragmentation.
2, bearing noise: Rolling bearings in the operation promised a subtle work noise; if the sound is too loud or there are abnormal noise or impact sound; then indicate that the bearing is faulty.
The reason for the noise of the rolling bearing is more complicated; 1) it is the external wear of the inner and outer rings of the bearing. Because this is worn, the cooperation between the bearing and the shell, the bearing and the shaft is broken; the axis is deviated from the correct orientation; When the shaft is moving at high speed, abnormal noise occurs. When the bearing is exhausted; its appearance metal falls off; it will also increase the radial gap of the bearing and cause abnormal noise. 2) The bearing is lacking in smoothness; the dry conflict is formed; and the bearing is broken, etc. The movement is static. 3) After the bearing wears loose, the cage is loose and damaged; the damage of the abnormal bearing will also occur. When the rolling bearing is disassembled, the bearing fault and the cause of the damage can be judged according to the damage condition of the bearing.
3. The metal surface of the raceway is detached: the bearing tumbling body and the inner and outer ring raceways all receive the effect of periodic pulsating load; then the contact stress changes during the attack cycle. When the number of stress cycles reaches a certain value; in the rollover or The inner and outer ring raceway work surface is fatigued and shedding. If the bearing load is too large, this fatigue will be aggravated. Others; the bearing device is not correct, the shaft is tortuous; the raceway will be off the surface. The bearing raceway Excessive shedding will reduce the accuracy of the shaft's work; it will cause tissue oscillations and noise.
4, bearing burns: burned bearings have tempering color on the raceway and roll body. The cause of burns is usually lack of smoothness, smooth oil quality does not meet the demand or transformation; and the bearing device is too tight.
5. Plastic deformation: the bearing raceway and the roller touch surface show uneven pits; clarify the plastic deformation of the bearing. The reason is that the bearing is under the effect of large static load or impact load; The yield limit of the data; this condition usually occurs on bearings that rotate at low speeds.
6, bearing seat crack: the cause of cracks in the bearing seat can be too tight bearing cooperation; bearing foreign or inner ring loose; bearing housing deformation; equipment bearing surface processing is not good.
7. The cage is broken: its cause is smooth lack; the rolling body is broken; the seat is inclined.
8. The metal of the cage adheres to the tumbling body; the reason for the ability is that the tumbling body is stuck in the cage or is lacking in smoothness.
9, the raceway raceway is severely worn: it can be a foreign object falling into the seat; the lack of smooth oil or the smooth oil trademark is not suitable.

---

Recommend to friends comments close window

Bearing related knowledge

Classification of rolling bearing fault diagnosis skills (2) Application and positioning of variable speed bearings The accuracy level of SKF bearings is how to distinguish the basic components of the rolling bearing.

This article links to http://
Please indicate China Bearing Network http://

Previous: Rolling mill bearing Next: Railway bearing quantitative grease machine

Non Woven Sanding Belt

Surface conditioning non woven Sanding Belt
This product is made of high quality nylon nonwoven material and great aluminum oxide. It is applicable to handheld and automatic grinding apparatus,with elasticity and small grind,can be good to improve the grinding workpiece ,and easy to replace.

Compared with the traditional abrasives products,nylon abrasive belts have the following advantages: can control the minimum amount of grinding mil,.grinding depth anti-blocking,the minimum of tolerance probability,new abrasives grain continuously exposed in the grinding process,and good effect.

The non-woven, open web, durable construction is designed to resist loading and greatly increase the life of the Belt. Standard Abrasive Non-Woven Discs and Belts offer repeatable finishes for a wide variety of applications.

Application:
Providing additional strength and durability for removing paints,rust, corrosion, exit burrs, weld splatter, parting lines and deburring on ferrous and nonferrous metals.
Blending weld seams and deburring edges

We distributes and wholesales various brands of Abrasive Sanding Disc, Cutting Wheels , Abrasive Flap Disc , Flap Wheels , Flap Disc Backing Pad, Flap Disc Adhesive , Abrasive Machine and Surface Conditioning Product etc, and enjoy a high position among consumers.

abrasive sanding belt non woven,Nylon abrasive sanding belts,nonwoven sanding belt,non woven sanding belts,sanding belt for surface conditioning

Zhengzhou Jiading Abrasive Manufacturing Co.,Ltd , https://www.jiadingabrasive.com